Proflo jetted tub manual

The unit must be connected to a circuit interrupter GFCI provided by the installer. The GFCI breaker should be tested on a routine basis. To test the GFCI breaker, push the test button. If the GFCI fails to operate in this manner there is ground current flowing, indicating the possibility of an electrical shock. Do not use the unit. Disconnect the unit and have the problem corrected by a qualified service representative before using. All pumps and blowers must be connected to a ground fault circuit interrupter GFCI protected outlets.

Standard Line Total Massage units can be operated on a single service. All heaters must be. Electrical outlet must be mounted 4" mm above the floor line and 12" max mm inside from the edge of the bathtub, or in accordance with local building and electrical codes.

Do not use electric extension cord to power the unit. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password.

Exercise caution when entering and exiting. You can only view or download manuals with. PF Jets: The jets can be easily adjusted by pointing the jet-nozzle in the desired direction.

The strength of the water flow and air induction can be regulated through twisting the jetnozzle. Twisting the nozzle counter-clockwise will decrease the water flow of that particular jet. If the nozzle is twisted clockwise then the water flow will increase up to its maximum flow.

Twisting the nozzle clockwise will decrease the water flow of that particular jet If the nozzle is twisted counter-clockwise then the water flow will increase up to its maximum flow. The whirlpool bath pump is activated by an on-off switch. Each depression of the switch will actuate the pump. If off, one depression will turn the pump on. If on, the next depression will turn it off.

Children should not be allowed to use these products without adult supervision. Pregnant women and those with heart conditions or other conditions that limit normal physical activity should consult a doctor before use. Finally, apply light buffing compound and buff area with a clean stitched cotton buffing pad or equivalent. Use an extra application of fine buffing compound if necessary.

For Cracks and Major surface damage, call our service line Check for incorrect or loose wire connections. Make sure the correct power supply is being used. Make sure that the jets are fully opened and water is flowing. Check for low voltage supply frequently caused by undersized wire.

Make sure the motor gets a fresh air supply and the vents are kept unclogged. Make sure that the motor shaft turns free. Check for jammed impeller or an obstruction on the volute casing. Check for low voltage and undersized wire. Check for clogged plumbing lines. Check compression fittings union connectors making sure they are properly aligned and secured.

Make sure the O-ring is properly seated and not damaged. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Exercise caution when entering and exiting. COM 3. Electrical Requirements and Information 1. COM 5. Framing and Installation Structural measurements should be verified against the actual bath received to ensure proper fit.

Reference for correct tile flange installation Use drawing below as a reference guide for rough-in measurements. COM 7. COM 9. Faucet deck mount dimensions Deck space where faucets can be mounted is given in diagonal dimension Y and base line dimension Z, which is the long side of the deck corner. Below are the recommended procedures for cleaning: DO NOT use powdered cleaners unless cleaner is fully dissolved in water. Operating Instructions 1.

COM Check Circuit Breakers. ProFlo Parts Contact us to place an order today! Latest News. ProFlo, Inc. Quick Links. Also, do not turn the switch on and off. It will take a couple seconds to turn on. Avoid using bubble bath if you plan on turning on the jets. According to ProFlo, you can use bath oils and the jets, but you will need to clean the jets more frequently. Rinse a ProFlo Jetted tub after each use.

Use a cup to help rinse away the sides of the tub. Wipe the sides with a soft rag or sponge where the top of the water was, in order to minimize a tub ring. Clean your tub weekly if you use it every day.